(this is the equal triangle, for TOSAM,
runtime 43 minutes)
(compensation for 1/4 bit, side length 17.5 inch)
(w/sub routine for cutting 4 triangles out of a 16"x 48"x 1/2" piece)
g90
g01 z0.1 f30
g01 x0 y0
m98 p777 (calling subroutine for first up triangle)
g00 x9.375 y15.372 (this is the x point forthe 1st upside down tri)
m98 p778
g90
g00 x18.75 y0 (this is new x point for 2nd up Triangle***check change)
m98 p777
g00 x28.125 y15.372 (this is the x point forthe 2nd upside down tri)
m98 p778
g90
m30
(************************************SUB-ROUTINES********************************)
(right side up triangle, relative)
O777
G90
G00 Z0.1
g01 z-.17 f5
(this is upright triangle, all the way around once RELATIVE)
g91
g01 x8.875 y15.372 f15
g01 x8.875 y-15.372 f15
g01 x-17.75
G90
g01 z-.39 f5
(this is upright triangle, all the way around once RELATIVE-2nd pass)
g91
g01 x8.875 y15.372 f15
g01 x8.875 y-15.372 f15
g01 x-17.75
G90
g01 z-.55 f5
(this is upright triangle, all the way around once RELATIVE- last pass)
g91
g01 x8.875 y15.372 f15
g01 x8.875 y-15.372 f15
g01 x-17.75
G90
g01 z.5 f25
M99
(Upside down, relative)
O778
G90
G00 Z0.1
g01 z-.17 f5
(this is upside-down triangle, all the way around once RELATIVE)
g91
g01 x8.875 y-15.372 f15
g01 x8.875 y15.372 f15
g01 x-17.75
G90
g01 z-.39 f5
(this is upside-down triangle, all the way around once RELATIVE-2nd pass)
g91
g01 x8.875 y-15.372 f15
g01 x8.875 y15.372 f15
g01 x-17.75
G90
g01 z-.55 f5
(this is upside-down triangle, all the way around once RELATIVE- last pass)
g91
g01 x8.875 y-15.372 f15
g01 x8.875 y15.372 f15
g01 x-17.75
G90
g01 z.5 f25
M99
(compensation for 1/4 bit, side length 17.5 inch)
(w/sub routine for cutting 4 triangles out of a 16"x 48"x 1/2" piece)
g90
g01 z0.1 f30
g01 x0 y0
m98 p777 (calling subroutine for first up triangle)
g00 x9.375 y15.372 (this is the x point forthe 1st upside down tri)
m98 p778
g90
g00 x18.75 y0 (this is new x point for 2nd up Triangle***check change)
m98 p777
g00 x28.125 y15.372 (this is the x point forthe 2nd upside down tri)
m98 p778
g90
m30
(************************************SUB-ROUTINES********************************)
(right side up triangle, relative)
O777
G90
G00 Z0.1
g01 z-.17 f5
(this is upright triangle, all the way around once RELATIVE)
g91
g01 x8.875 y15.372 f15
g01 x8.875 y-15.372 f15
g01 x-17.75
G90
g01 z-.39 f5
(this is upright triangle, all the way around once RELATIVE-2nd pass)
g91
g01 x8.875 y15.372 f15
g01 x8.875 y-15.372 f15
g01 x-17.75
G90
g01 z-.55 f5
(this is upright triangle, all the way around once RELATIVE- last pass)
g91
g01 x8.875 y15.372 f15
g01 x8.875 y-15.372 f15
g01 x-17.75
G90
g01 z.5 f25
M99
(Upside down, relative)
O778
G90
G00 Z0.1
g01 z-.17 f5
(this is upside-down triangle, all the way around once RELATIVE)
g91
g01 x8.875 y-15.372 f15
g01 x8.875 y15.372 f15
g01 x-17.75
G90
g01 z-.39 f5
(this is upside-down triangle, all the way around once RELATIVE-2nd pass)
g91
g01 x8.875 y-15.372 f15
g01 x8.875 y15.372 f15
g01 x-17.75
G90
g01 z-.55 f5
(this is upside-down triangle, all the way around once RELATIVE- last pass)
g91
g01 x8.875 y-15.372 f15
g01 x8.875 y15.372 f15
g01 x-17.75
G90
g01 z.5 f25
M99